|Theme||Visible||Selectable||Appearance||Zoom Range (now: 0)|
Nicholson, A. Kirby (Pressure Diagnostics Ltd.) | Bachman, Robert C. (Pressure Diagnostics Ltd.) | Scherz, R. Yvonne (Endeavor Energy Resources) | Hawkes, Robert V. (Cordax Evaluation Technologies Inc.)
Abstract Pressure and stage volume are the least expensive and most readily available data for diagnostic analysis of hydraulic fracturing operations. Case history data from the Midland Basin is used to demonstrate how high-quality, time-synchronized pressure measurements at a treatment and an offsetting shut-in producing well can provide the necessary input to calculate fracture geometries at both wells and estimate perforation cluster efficiency at the treatment well. No special wellbore monitoring equipment is required. In summary, the methods outlined in this paper quantifies fracture geometries as compared to the more general observations of Daneshy (2020) and Haustveit et al. (2020). Pressures collected in Diagnostic Fracture Injection Tests (DFITs), select toe-stage full-scale fracture treatments, and offset observation wells are used to demonstrate a simple workflow. The pressure data combined with Volume to First Response (Vfr) at the observation well is used to create a geometry model of fracture length, width, and height estimates at the treatment well as illustrated in Figure 1. The producing fracture length of the observation well is also determined. Pressure Transient Analysis (PTA) techniques, a Perkins-Kern-Nordgren (PKN) fracture propagation model and offset well Fracture Driven Interaction (FDI) pressures are used to quantify hydraulic fracture dimensions. The PTA-derived Farfield Fracture Extension Pressure, FFEP, concept was introduced in Nicholson et al. (2019) and is summarized in Appendix B of this paper. FFEP replaces Instantaneous Shut-In Pressure, ISIP, for use in net pressure calculations. FFEP is determined and utilized in both DFITs and full-scale fracture inter-stage fall-off data. The use of the Primary Pressure Derivative (PPD) to accurately identify FFEP simplifies and speeds up the analysis, allowing for real time treatment decisions. This new technique is called Rapid-PTA. Additionally, the plotted shape and gradient of the observation-well pressure response can identify whether FDI's are hydraulic or poroelastic before a fracture stage is completed and may be used to change stage volume on the fly. Figure 1: Fracture Geometry Model with FDI Pressure Matching Case studies are presented showing the full workflow required to generate the fracture geometry model. The component inputs for the model are presented including a toe-stage DFIT, inter-stage pressure fall-off, and the FDI pressure build-up. We discuss how to optimize these hydraulic fractures in hindsight (look-back) and what might have been done in real time during the completion operations given this workflow and field-ready advanced data-handling capability. Hydraulic fracturing operations can be optimized in real time using new Rapid-PTA techniques for high quality pressure data collected on treating and observation wells. This process opens the door for more advanced geometry modeling and for rapid design changes to save costs and improve well productivity and ultimate recovery.
Abstract Characterization of hydraulic fracture system in multi-fractured horizontal wells (MFHW) is one of the key steps in well spacing optimization of tight and shale reservoirs. Different methods have been proposed in the industry including core-through, micro-seismic, off-set pressure data monitoring during hydraulic fracturing, pressure depletion mapping, rate-transient analysis, pressure-transient analysis, and pressure interference test. Pressure interference test for a production and monitoring well pair includes flowing the production well at a stable rate while keeping the monitoring well shut-in and recording its pressure. In this study, the coupled flow of gas in hydraulic fractures and matrix systems during pressure interference test is modeled using an analytical method. The model is based on Laplace transform combined with pseudo-pressure and pseudo-time. The model is validated against numerical simulation to make sure the inter-well communication test is reasonably represented. Two key parameters were introduced and calculated with time using the analytical model including pressure drawdown ratio and pressure decline ratio. The model is applied to two field cases from Montney formation. In this case, two wells in the gas condensate region of Montney were selected for a pressure interference test. The monitoring well was equipped with downhole gauges. As the producing well was opened for production, the bottom-hole pressure of the monitoring well started declining at much lower rate than the production well. The pressure decline rate in the monitoring well eventually approached that of the producing well after days of production. This whole process was modeled using the analytical model of this study by adjusting the conductivity of the communicating fractures between the well pairs. This study provides a practical analytical tool for quantitative analysis of the interference test in MFHWs. This model can be integrated with other tools for improved characterization of hydraulic fracture systems in tight and shale reservoirs.
Abstract Distributed Fiber Optics (DFO) technology has been the new face for unconventional well diagnostics. This technology focuses on measuring Distributed Acoustic Sensing (DAS) and Distrusted Temperature Sensing (DTS) to give an in-depth understanding of well productivity pre and post stimulation. Many different completion design strategies, both on surface and downhole, are used to obtain the best fracture network outcome; however, with complex geological features, different fracture designs, and fracture driven interactions (FDIs) effecting nearby wells, it is difficult to grasp a full understanding on completion design performance for each well. Validating completion designs and improving on the learnings found in each data set should be the foundation in developing each field. Capturing a data set with strong evidence of what works and what doesn't, can help the operator make better engineering decisions to make more efficient wells as well as help gauge the spacing between each well. The focus of this paper will be on a few case studies in the Bakken which vividly show how infill wells greatly interfered with production output. A DFO deployed with a 0.6" OD, 23,000-foot-long carbon fiber rod to acquire DAS and DTS for post frac flow, completion, and interference evaluation. This paper will dive into the DFO measurements taken post frac to further explain what effects are seen on completion designs caused by interferences with infill wells; the learnings taken from the DFO post frac were applied to further escalate the understanding and awareness of how infill wells will preform on future pad sites. A showcase of three separate data sets from the Bakken will identify how effective DFO technology can be in evaluating and making informed decisions on future frac completions. In this paper we will also show and discuss how DFO can measure real time FDI events and what measures can be taken to lessen the impact on negative interference caused by infill wells.
Zeinabady, Danial (University of Calgary) | Zanganeh, Behnam (University of Calgary, Chevron Canada Resources) | Shahamat, Sadeq (Birchcliff Energy Ltd.) | Clarkson, Christopher R. (University of Calgary)
Abstract The DFIT flowback analysis (DFIT-FBA) method, recently developed by the authors, is a new approach for obtaining minimum in-situ stress, reservoir pressure, and well productivity index estimates in a fraction of the time required by conventional DFITs. The goal of this study is to demonstrate the application of DFIT-FBA to hydraulic fracturing design and reservoir characterization by performing tests at multiple points along a horizontal well completed in an unconventional reservoir. Furthermore, new corrections are introduced to the DFIT-FBA method to account for perforation friction, tortuosity, and wellbore unloading during the flowback stage of the test. The time and cost efficiency associated with the DFIT-FBA method provides an opportunity to conduct multiple field tests without delaying the completion program. Several trials of the new method were performed for this study. These trials demonstrate application of the DFIT-FBA for testing multiple points along the lateral of a horizontal well (toe stage and additional clusters). The operational procedure for each DFIT-FBA test consists of two steps: 1) injection to initiate and propagate a mini hydraulic fracture and 2) flowback of the injected fluid on surface using a variable choke setting on the wellhead. Rate transient analysis methods are then applied to the flowback data to identify flow regimes and estimate closure and reservoir pressure. Flowing material balance analysis is used to estimate the well productivity index for studied reservoir intervals. Minimum in-situ stress, pore pressure and well productivity index estimates were successfully obtained for all the field trials and validated by comparison against a conventional DFIT. The new corrections for friction and wellbore unloading improved the accuracy of the closure and reservoir pressures by 4%. Furthermore, the results of flowing material balance analysis show that wellbore unloading might cause significant over-estimation of the well productivity index. Considerable variation in well productivity index was observed from the toe stage to the heel stage (along the lateral) for the studied well. This variation has significant implications for hydraulic fracture design optimization, particularly treatment pressures and volumes.
Abstract Recovery factor for multi-fractured horizontal wells (MFHWs) at development spacing in tight reservoirs is closely related to the effective horizontal and vertical extents of the hydraulic fractures. Direct measurement of pressure depletion away from the existing producers can be used to estimate the extent of the hydraulic fractures. Monitoring wells equipped with downhole gauges, DFITs from multiple new wells close to an existing (parent) well, and calculation of formation pressure from drilling data are among the methods used for pressure depletion mapping. This study focuses on acquisition of pressure depletion data using multi-well diagnostic fracture injection tests (DFITs), analysis of the results using reservoir simulation, and integration of the results with production data analysis of the parent well using rate-transient analysis (RTA) and reservoir simulation. In this method, DFITs are run on all the new wells close to an existing (parent) well and the data is analyzed to estimate reservoir pressure at each DFIT location. A combination of the DFIT results provides a map of pressure depletion around the existing well, while production data analysis of the parent well provides fracture conductivity and surface area and formation permeability. Furthermore, reservoir simulation is tuned such that it can also match the pressure depletion map by adjusting the system permeability and fracture geometry of the parent well. The workflow of this study was applied to two field case from Montney formation in Western Canadian Sedimentary Basin. In Field Case 1, DFIT results from nine new wells were used to map the pressure depletion away from the toe fracture of a parent well (four wells toeing toward the parent well and five wells in the same direction as the parent). RTA and reservoir simulation are used to analyze the production data of the parent well qualitatively and quantitatively. The reservoir model is then used to match the pressure depletion map and the production data of the parent well and the outputs of the model includes hydraulic fracture half-lengths on both sides of the parent well, formation permeability, fracture surface area and fracture conductivity. In Field Case 2, the production data from an existing well and DFIT result from a new well toeing toward the existing wells were incorporated into a reservoir simulation model. The model outputs include system permeability and fracture surface area. It is recommended to try the method for more cases in a specific reservoir area to get a statistical understanding of the system permeability and fracture geometry for different completion designs. This study provides a practical and cost-effective approach for pressure depletion mapping using multi-well DFITs and the analysis of the resulting data using reservoir simulation and RTA. The study also encourages the practitioners to take every opportunity to run DFITs and gather pressure data from as many well as possible with focus on child wells.
Hui, Gang (University of Calgary, Alberta, Canada) | Chen, Shengnan (University of Calgary, Alberta, Canada) | Gu, Fei (PetroChina Research Institute of Petroleum Exploration and Development, Beijing, China)
Abstract The recent seismicity rate increase in Fox Creek is believed to be linked to the hydraulic fracturing operations near the region. However, the spatiotemporal evolution of hydraulic fracturing-induced seismicity is not well understood. Here, a coupled approach of geology, geomechanics, and hydrology is proposed to characterize the spatiotemporal evolution of hydraulic fracturing-induced seismicity. The seismogenic faults in the vicinity of stimulated wells are derived from the focal mechanisms of mainshock event and lineament features of induced events. In addition, the propagation of hydraulic fractures is simulated by using the PKN model, in combination with inferred fault, to characterize the possible well-fault hydrological communication. The original stress state of inferred fault is determined based on the geomechanics analysis. Based on the poroelasticity theory, the coupled flow-geomechanics simulation is finally conducted to quantitatively understand the fluid diffusion and poroelastic stress perturbation in response to hydraulic fracturing. A case study of a moment-magnitude-3.4 earthquake near Fox Creek is utilized to demonstrate the applicability of the coupled approach. It is shown that hydraulic fractures propagated along NE45° and connected with one North-south trending fault, causing the activation of fault and triggered the large magnitude event during fracturing operations. The barrier property of inferred fault under the strike-slip faulting regime constrains the nucleation position of induced seismicity within the injection layer. The combined changes of pore pressure and poroelastic stress caused the inferred fault to move towards the failure state and triggered the earthquake swarms. The associated spatiotemporal changes of Coulomb Failure Stress along the fault plane is well in line with the spatiotemporal pattern of induced seismicity in the studied case. Risks of seismic hazards could be reduced by decreasing fracturing job size during fracturing stimulations.
Rodríguez-Pradilla, Germán (School of Earth Sciences, University of Bristol, UK.) | Eaton, David (Department of Geoscience, University of Calgary, Canada.) | Popp, Melanie (geoLOGIC Systems Ltd., Calgary, Canada.)
Abstract The goal of this work is to calibrate a regional predictive model for maximum magnitude of seismic activity associated with hydraulic-fracturing in low-permeability formations in the Western Canada Sedimentary Basin (WCSB). Hydraulic fracturing data (i.e. total injected volume, injection rate, and pressure) were compiled from more than 40,000 hydraulic-fractured wells in the WCSB. These wells were drilled into more than 100 different formations over a 20-year period (January 1st, 2000 and January 1st, 2020). The total injected volume per unit area was calculated utilizing an area of 0.2° in longitude by 0.1° in latitude (or approximately 13x11km, somewhat larger than a standard township of 6x6 miles). This volume was then used to correlate with reported seismicity in the same unit areas. Collectively, within the 143 km area considered in this study, a correlation between the total injected volume and the maximum magnitude of seismic events was observed. Results are similar to the maximum-magnitude forecasting model proposed by A. McGarr (JGR, 2014) for seismic events induced by wastewater injection wells in central US. The McGarr method is also based on the total injected fluid per well (or per multiple nearby wells located in the same unit area). However, in some areas in the WCSB, lower injected fluid volumes than the McGarr model predicts were needed to induce seismic events of magnitude 3.0 or higher, although with a similar linear relation. The result of this work is the calculation of a calibration parameter for the McGarr model to better predict the magnitudes of seismic events associated with the injected volumes of hydraulic fracturing. This model can be used to predict induced seismicity in future unconventional hydraulic fracturing treatments and prevent large-magnitude seismic events from occurring. The rich dataset available from the WCSB allowed us to carry out a robust analysis of the influence of critical parameters (such as the total injected fluid) in the maximum magnitude of seismic events associated with the hydraulic-fracturing stimulation of unconventional wells. This analysis could be replicated for any other sedimentary basin with unconventional wells by compiling similar stimulation and earthquake data as in this study.
Soroush, Mohammad (RGL Reservoir Management, University of Alberta) | Mohammadtabar, Mohammad (RGL Reservoir Management, University of Alberta) | Roostaei, Morteza (RGL Reservoir Management) | Hosseini, Seyed Abolhassan (RGL Reservoir Management, University of Alberta) | Mahmoudi, Mahdi (RGL Reservoir Management) | Keough, Daniel (Precise Downhole Services Ltd) | Cheng, Li (University of Alberta) | Moez, Kambiz (University of Alberta) | Fattahpour, Vahidoddin (RGL Reservoir Management)
Abstract Distributed Temperature Sensing (DTS) system using optical fiber has been deployed for downhole monitoring over two-decades. Several technological advancements led to a wide acceptance of this technology as a reliable surveillance technique. This paper presents a comprehensive technical review of all the applications of the DTS, with focus on oil and gas industrial deployments. The paper starts with the advantages of the DTS over other methods and an overview of the DTS basics, including theory, the DTS components, deployment types, fiber types, design and limitations. Then, it is followed by the oil and gas applications of the DTS including hydraulic fracturing (during and after fracturing), well treatment/stimulation (acid injection, fluid distribution, diversion monitoring), inorganic (scaling) and organic (wax/asphaltene/hydrate) deposition detection, leak detection (in well and pipeline), flow monitoring (rate monitoring, water/steam injection and SAGD monitoring, CO2 storage monitoring, zonal contribution determination, gas lift optimization) and reservoir/fluid characterization (facies, porosity, permeability and fluid composition determination). This study reviews the historical development, applications and limitations of the DTS systems. The paper mainly focusses on deployment techniques, the application of the DTS for the prediction and surveillance of the non-thermal and thermal producer/injector wells, hydraulically fractured wells and those wells with treatments. The paper provides a concise review using several field cases from over two hundred published papers of Society of Petroleum Engineering (SPE) and journal databases. The application of the DTS in downhole monitoring can be divided into the qualitative and quantitative applications. In quantitative approaches, numerical models should be combined with the DTS data. This study discusses case by case worldwide field applications of DTS along with proposed modeling methods and interpretations. It also summarizes main challenges, including the fiber reliability, longevity, and operational limitations such as the installation and the complexity of quantitative approaches. This study is the foundation for an ongoing study on wellbore and reservoir surveillance through real-time distributed fiber optic sensing recordings along the wellbore. It summarizes the historical development and limitations to identify the existing gaps and reviews the lessons learned through the two decades of the application of the DTS in production performance.
Hosseini, Seyed Abolhassan (RGL Reservoir Management Inc., University of Alberta) | Roostaei, Morteza (RGL Reservoir Management Inc.) | Mohammadtabar, Farshad (RGL Reservoir Management Inc.) | Mohammadtabar, Mohammad (RGL Reservoir Management Inc., University of Alberta) | Soroush, Mohammad (RGL Reservoir Management Inc., University of Alberta) | Berner, Kelly (RGL Reservoir Management Inc.) | Mahmoudi, Mahdi (RGL Reservoir Management Inc.) | Miller, Roger (Pacific Perforating Inc.) | Fattahpour, Vahidoddin (RGL Reservoir Management Inc.)
Abstract Development of weakly and unconsolidated sand reservoirs require effective sand control media to prevent sand production. The existing sand control devices in the market are either relying on surface filtration to prevent sand production through size exclusion or bridging or depth filtration which relies on the pore size distribution of a porous filter or pack to prevent the sand from producing along the production fluids. In this study, we introduce a new hybrid sand screen that works based on a combined surface and depth filtration. Radial Sand Control Evaluation (RSCE) testing facility was used to compare the solid production and flow performance of the new hybrid screen with various mesh media in multi-phase gas and liquid flow under various fluid injection scenarios. Solid production and flow performance were compared with investigated cases. The new hybrid screen provides an optimized Open to Flow Area (OFA) in comparison to available surface filtration or depth filtration media, which provides required OFA, while prevents sanding. The robust design, low cost and manufacturing ease make it a suitable screen media for most sand control applications. The sand retention test results under various fluid injection scenarios including multi-phase oil, brine, and gas show that it outperforms the Dutch Twill (DT) weave and Reverse Dutch Twill (RDT) weave of equivalent aperture size, with better flow performance at constant flow rate tests compare to best-performing mesh media, while keeping the produced sand far below the acceptable thresholds. Hybrid design handles both high velocity and high Gas-Oil Ratio (GOR) better than equivalent depth filtration media of equivalent size. This paper presents a detailed characterization, flow performance testing of a new hybrid sand control media that combines the surface filtration and depth filtration properties to achieve better solid retention and flow performance. The hybrid screen media is suitable for high-rate producers with high GOR. Keywords: Hybrid Screen, Surface Filtration, Depth Filtration, Radial Sand Control Evaluation (RSCE) Testing
Abstract Flow Control Device (FCD) completions in steam assisted thermal applications have been implemented in several places: Canada, California, China, Oman and Colombia, among others. Such completion configurations have been more common in recent years to mitigate or avoid uneven and/or improper steam placement and steam breakthrough, which are some of the critical issues operators have experienced in these developments. This study presents different FCD technologies designed to optimize the steam injection and fluids production for diverse steam assisted applications including SAGD, CSS and Steam Flooding. Three FCD technologies are introduced: (i) supersonic steam injection FCD, (ii) steam choking FCD and (iii) multi-directional FCD. Extensive Computational Fluid Dynamic (CFD) simulations, analytic near-wellbore simulations and flow loop testing were conducted to evaluate the performance of the three technologies: (i) the supersonic steam injection FCD showed a high pressure recovery (therefore, less upstream pressure requirements) and a reduction of the cumulative steam-oil ratio, (ii) the steam choking FCD demonstrated the highest steam choking capability for these type of devices and (iii) the multi-directional FCD showed promising results for CSS applications to allow for supersonic steam injection during the injection phase and steam choking capabilities during the production phase Common FCD deployment risks such as erosion, scaling potential and high pressure drops were reviewed to provide the reader with a high level understanding of the factors which could induce these issues. Finally, field data where FCD completions have been installed is presented to compare the FCD wells performance versus conventional well designs and illustrate the success of these completions strategies. Keywords: flow control devices, supersonic steam injection, steam choking