|Theme||Visible||Selectable||Appearance||Zoom Range (now: 0)|
Gupta, M K (Oil and Natural Gas Corporation Ltd.) | Sukanandan, J N (Oil and Natural Gas Corporation Ltd.) | Singh, V K (Oil and Natural Gas Corporation Ltd.) | Pawar, A S (Oil and Natural Gas Corporation Ltd.) | Deuri, Budhin (Oil and Natural Gas Corporation Ltd.)
In one of the offshore complex of ONGC, Carryover of liquid have been observed leading to tripping of gas compressors resulting a loss of significant amount of production. It was established that separation capacity of existing separators even at present operating conditions were not sufficient to process present production. Further an increase of 60% of present gas production is envisaged as per long term production profile. Hence, handling the present and envisaged increased production in the existing separators was explored.
To handle the envisaged enhanced production rate and to avoid carryover issue in existing separators, options such as feed nozzles enhancement and installation of inlet device was explored. Changing feed nozzles is a tedious job, require hot job and longer shut down period and requires complete integrity test of separators as recommended by ASME SEC-VIII, pressure vessel guidelines followed by R-stamping. Therefore modifications in separator internal was suggested which will enhance the separation capacity and can accommodate in the present and envisaged increase of future production.
The analysis revealed that even though the diameter and length of the separators are adequate to handle the load, it was established that the inlet nozzle of the separators are not adequate. Hence, considering many factors such as minimum pressure drop, ensuring good gas distribution, suppression of re-entrainment, momentum reduction and erosion velocity ratio of less than one, modifications in separator internal was suggested which will enhance the separation capacity and can accommodate the present and future envisaged increase of production of more than 60%. It was established in the study that this options of installation of inlet device can be done with minimum modifications and require minimum shutdown period. This option has been recommended and is under field implementation. Hence this work will provide a significant help to oil and gas personal to accommodate higher than design feed quantities in existing separators with minimum modifications and minimum shutdown period.
Foaming in absorber column for sour gas treatment using amine is a common problem which adversely affects column performance leading to reduction in sales and fuel-gas production and solvent loss. Mostly antifoam injection has been a common method to counter the foaming, large dosage and frequent dosing of antifoam many a times aggravates the problem. This study details an alternative technique based on pressure pulse mechanism to control foaming in one of ONGC's gas sweetening plants.
One of ONGC's amine based sour gas sweetening plants faced severe foaming problem frequently. The feed rate is 200 kscm/hr and absorber column operating pressure is 51 kg/cm2. The experiment utilizes the property of surface tension which fluctuates with change in pressure of the system leading to foam collapse. The experimental procedure involved varying the sour gas feed rate, thereby creating pressure pulse inside the absorber column. Differential pressure across the column which is an indicator of foaming tendency is then monitored and controlled within 1.0 kg/cm2 and recorded for establishing effectiveness of the method.
It is observed that by providing a number of cycles of pressure pulse in the absorber, the differential pressure stabilizes gradually which indicates collapse of foam. It shows that whenever there is increase in feed, expansion of bubble takes place which provides high interfacial liquid-vapour contact. On the other hand whenever there is decrease in feed rate, compression of bubble takes place which provides low interfacial liquid-vapour contact. Surface layer surrounding the bubbles in a foam acts as a membrane or skin that can stretch or relax in response to change in pressure and gives a mechanical shock which breaks the bubble. The increase of size ultimately leads to instability and break-up of the upper surface and releases the liquid holdup. Hence by using feed rate spikes, the pressure of the bubble is pulsed to higher levels and returned to substantially the original level. This cycle continues for a selected number of times so that this pressure pulse travels through the liquid and bubbles and affects its surface tension. This results into a transition phase which in very high energy level breaks the bubble and releases the gas and decreases the liquid hold up and controls the foaming phenomenon.
This paper will gives an insight into a novel methodology of mitigating foaming problem in a sour gas treating absorber just by varying the feed rates in a controlled manner. This technique eliminates the need for injecting antifoam agents which in turn will reduce the operating expenditure of the plant. Adverse impact on environment due to excessive use of antifoam agent is also minimized.
Devshali, Sagun (Oil and Natural Gas Corporation Ltd.) | Manchalwar, Vinod (Oil and Natural Gas Corporation Ltd.) | Deuri, Budhin (Oil and Natural Gas Corporation Ltd.) | Malhotra, Sanjay Kumar (Oil and Natural Gas Corporation Ltd.) | Prasad, Bulusu V.R.V. (Oil and Natural Gas Corporation Ltd.) | Yadav, Mahendra (Oil and Natural Gas Corporation Ltd.) | Kumar, Avinav (Oil and Natural Gas Corporation Ltd.) | Uniyal, Rishabh (Oil and Natural Gas Corporation Ltd.)
The paper describes the feasibility of revisiting old sands, for improving the recovery factors and enhancing production, which otherwise were already abandoned. The paper also outlines the systematic methods for predicting the onset of liquid loading in gas wells, evaluation of completions for optimization and comparison of various deliquification techniques. ONGC is operating in two gas fields in eastern and western regions in India. Earlier in both the fields, many sands had to be closed/isolated after the wells ceased to flow due to liquid loading in the absence of continuous deliquification. In order to predict liquid loading tendencies and identify opportunities for production enhancement, performance of 150 gas wells has been analyzed. To select most suitable deliquification technique for the present condition, all technically feasible methods have been evaluated and compared in order to get the maximum ultimate gas recovery possible.
After an extensive study, 3 wells were identified in the preliminary stage and SRP was selected as the most suitable Deliquification technique. Initially, two non-flowing wells, which had ceased due to liquid loading and were about to be abandoned, were selected. After SRP installation and sustained unloading of water for about 30 days, these wells started producing 12000 SCMD gas. In the third well, one of the top sands had earlier been isolated due to liquid loading and production history indicated that the isolated sand had a very good potential. Also, production from the well was declining in the current bottom operating sand as well due to liquid loading. Encouraged by the results that deliquification had yielded in the initial two gas wells, the isolated sand interval in the third well was opened again with the aim to revive production. The well was re-completed with SRP with both the reservoirs open. Before deliquification, the well was producing about 15000 SCMD gas from the bottom sand. After SRP installation and continuous deliquification, the well started producing gas at a stabilized rate of 45000 SCMD, thereby resulting in an additional gas recovery of 30000 SCMD for nearly one year as on date. The approach of putting in place continuous deliquification techniques has not only helped in enhancing production from the existing reservoirs, but has also opened up new avenues to revisit the earlier isolated / abandoned reservoirs for possible enhanced recoveries.
Gupta, M K (Oil and Natural Gas Corporation Ltd.) | Sukanandan, J N (Oil and Natural Gas Corporation Ltd.) | Singh, V K (Oil and Natural Gas Corporation Ltd.) | Bansal, R (Oil and Natural Gas Corporation Ltd.) | Pawar, A S (Oil and Natural Gas Corporation Ltd.) | Deuri, Budhin (Oil and Natural Gas Corporation Ltd.)
This paper discusses a case study of one of the onshore field of ONGC where while processing well fluid, frequent surge has been observed leading to shutdown of the SDVs creating severe operational problems and loss of production. It was imperative to find out the problematic wells/lines located in clusters which contribute for surge formation and mitigation approach with minimum modifications.
A transient complex network of sixty five wells flowing with a different lift mode such as intermittent gas lift, continuous gas lift etc were developed in a dynamic multiphase flow simulator OLGA. Time cycle of each well were introduced for intermittent lift wells. Simulation study reveals pulsating transient trends of liquid flow, pressure which was matched with the real time data of the plant and hence confirms the accuracy of the model. After verifying the results, different scenarios were created to determine the causes of surge formation. After finding the cause, a low cost approach was considered for surge mitigations.
An integrated rigorous simulation was carried out in OLGA, by feeding more than 12,000 data points to obtain model match. Several scenarios were also created such as optimization of lift gas quantity, optimization of elevation and size. Trend obtained after each scenario was pulsating behaviour and it matched with the real time data appearing in the SCADA system of the field. After rigorous simulation with each scenario, it was established that the cause of surge forming wells/pipelines. Once the root cause of surge has been confirmed then quantum of liquid generated due to surge was determined. Adequacy checks of the existing separators were carried out to estimate the handling capacity of the existing separators at prevalent operating condition. After adequacy check it was found that existing separators cannot handle the surge generated in that time interval leading to cross the high-high safety level, resulting closure of shut down valve (SDV). After establishment of root cause of the surge, a low cost solution with small modification in pipelines and control system/valves was adopted to arrest the surges. It was first of its kind simulation carried out for a huge network of wells/ pipelines by feeding more than 12,000 data to analyze the surge formation cause and capture its dynamism owing to wide array of suspected causes. This will help to address the challenges of efficiently reviewing the entire pipeline network while designing new well pad/GGS and will also help to arrest surge by adopting a low cost solution wherever such situation arises.
Hazarika, Simanta (Oil & Natural Gas Corporation Ltd) | Rathod, P. Ramulu (Oil & Natural Gas Corporation Ltd) | Burla, Ravishankar (Oil & Natural Gas Corporation Ltd) | Das, Gour Chandra (Oil & Natural Gas Corporation Ltd) | Rao, Bkvrl (Oil & Natural Gas Corporation Ltd) | Deuri, Budhin (Oil & Natural Gas Corporation Ltd)
Subsea flow lines in deep water are typically exposed to high pressure and low temperature conditions which can create problems due to formation of gas hydrate. The gas hydrate formed can plug the flow lines causing not only loss of production, but may also create severe safety and environmental hazard. Moreover, dissociation of these plugs may take weeks or even months. Assessment of the hydrate formation potential during both steady is therefore an essential part of field development studies. The paper presents a case study of a gas field located in KG basin of India which was brought on production in 2018. The objective of the study was to assist the on-site team on issues related to hydrate inhibition during ongoing initial startup operation and assess the arrival time of rich MEG in the onshore plant in view of turn down flow conditions during commissioning. The study also demonstrates how the transient simulations helped to monitor progress, identify and respond quickly to address the challenges during initial startup operation of the deepwater gas field in Indian east coast. It emphasizes the need for accurate estimation of rich MEG arrival time and the minimum required gas flow rate from the subsea wells to ensure timely return of rich MEG to the onshore plant in order to avoid disruption in hydrate inhibition in the subsea system.