Geosteering and real time reservoir characterization were used to reduce the uncertainty. Reservoirs consisting of heterogeneous carbonates and shaly sands pose formation evaluation challenges for conventional logging-while-drilling (LWD) measurements. Magnetic resonance techniques hold promise for improving understanding of these reservoirs.
Results to date are compared with previous performance in the Gulf of Thailand (GoT). Reservoirs consisting of heterogeneous carbonates and shaly sands pose formation evaluation challenges for conventional logging-while-drilling (LWD) measurements. Magnetic resonance techniques hold promise for improving understanding of these reservoirs. This paper discusses ultradeep directional-resistivity (DDR) logging-while-drilling (LWD) measurements for high-angle and horizontal wells that have been applied recently with success on the Norwegian continental shelf (NCS). Determining the fluid properties of a reservoir by using pressure/volume/temperature (PVT) analysis is essential to petroleum reservoir studies, production equipment design, and reservoir recovery efficiency estimation.
Content of PetroWiki is intended for personal use only and to supplement, not replace, engineering judgment. SPE disclaims any and all liability for your use of such content. A technique using a suite of logs that are part of the drilling BHA. The formation properties are measured while drilling (although 40 to 60 feet back from the bit) and the information is pulsed to the surface.
MWD is now standard practice in offshore directional wells, where the tool cost is offset by rig time and wellbore stability considerations if other tools are used. The measurements are made downhole, stored in solid-state memory for some time and later transmitted to the surface. Data transmission methods vary from company to company, but usually involve digitally encoding data and transmitting to the surface as pressure pulses in the mud system. These pressures may be positive, negative or continuous sine waves. MWD tools that measure formation parameters (resistivity, porosity, sonic velocity, gamma ray) are referred to as logging-while-drilling (LWD) tools.
Use of magnetic-resonance-image (MRI) logging is growing as a logging while drilling (LWD) tool. The use of chemical nuclear sources downhole has been a logistical and management headache. MRI, by measuring in real time the free-fluid, capillary-bound-water, and clay-based-water volumes, offers an alternative, lithology-independent porosity measurement in complex lithologies. It can be used for geosteering and geostopping when sufficient productive formation has been exposed to the wellbore. Like most measurements, at an initial phase there are specialist applications that are more susceptible to realizing the value of magnetic-resonance logging.
Logging while drilling (LWD) refers to the addition of wireline-quality formation measurements to the directional data of a Measurement While Drilling (MWD) service. Although attempts to deliver LWD serices date back to the 1920's, the first viable tools were by J.J. Arps in the 1960's, but these did not become a commercial service. The growth of MWD in the late 1970's and early 1980's delivered the first commercial LWD services by the major service providers. The initial tools were natural gamma and resistivity, and these made geosteering possible, as horizontal drilling grew.
No other technology used in petroleum-well construction has evolved more rapidly than measurement while drilling (MWD) and logging while drilling (LWD). Early in the history of the oil field, drillers and geologists often debated conditions at the drillbit. With advances in electronic components, materials science, and battery technology, it became technically feasible to make measurements at the bit, and transmit them to the surface so that the questions could be answered. Directional measurements were the first measurements to have commercial application, with almost all use in offshore, directionally drilled wells. As long as MWD achieved certain minimum-reliability targets, it was less costly than single shots, and it gained popularity accordingly.
Baker Hughes drilled one horizontal well for major Indian operating company in a, low resistivity contrast field, onshore India. The candidate field / basin is a proved petroliferous basin, located in the northeastern corner of India.
The scope of work for this project involved integrating geological and open hole offset parameters to build a Geosteering model. Integrated data included a study of offset well data from the field, regional and local dip analysis from wellbore images, and a review of structural maps. Successful integration of these data helped to steer the well in the desired zone as per plan and make the best use of the data and to reduce uncertainties in Geosteering, drilling. Although high-quality 16-sector images commonly yield bedding dip, fracture and other geological information, this paper emphasizes how real-time reservoir navigation decisions was made using Geosteering modelling, real-time image processing, dip picking study etc.
Kisku, Sayanima (Oil & Natural Gas Corporation Ltd.) | Santhosh Kumar, R. (Oil & Natural Gas Corporation Ltd.) | Dayal, Har sharad (Oil & Natural Gas Corporation Ltd.) | Chadha, Harish Kumar (Oil & Natural Gas Corporation Ltd.) | Srivastava, Anil (Oil & Natural Gas Corporation Ltd.)
Infill drilling is an integral part of brown field management for exploiting un-drained areas with good oil saturation. In a matured field on water-flood, the primary objective is optimized wellbore placement of infill wells in areas with better petro-physical characteristics, bypassing flooded region. It is also important to design a robust completion strategy to safeguard the longevity of these wells by curtailing produced water. This approach assists in dramatic increase in production by isolating water charged sections and thereby restricting rise in water production.
The use of advanced Logging-While-Drilling techniques during horizontal drilling provides an opportunity for effective well planning. Real-time Logging-While-Drilling instruments during directional drilling gives us the opportunity to acquire information pertaining to the reservoir in a single run. Interpretation from the real-time data acquisition boosts the planning during wellbore drilling.
This paper discusses a case study of a field in western offshore, India, which focuses on the applications of geosteering and the use of swell packers for zonal isolation to augment oil production. In this study, two wells have been deliberated where the real-time information has been extracted and included in the decision making process. The bottom-hole assembly used in this case, comprised standard Logging-While-Drilling services such as gamma ray, resistivity, neutron porosity, density and density imaging services and also formation pressure testing.
Since the field under study is a carbonate reservoir that has been on waterflood for the last twenty eight years, chances of early breakthrough of water in the infill wells has posed a high risk in spite of the presence of good bypassed oil saturation. Geosteering has enabled to restrict the horizontal section safely within the desired zone of better oil saturation and geological features, as interpreted from the Logging-While-Drilling data. Further isolation of suspected water bearing zones with swell packers have assisted in healthy well completion by diminishing chances of sharp rise in water cut in the infill wells.