|Theme||Visible||Selectable||Appearance||Zoom Range (now: 0)|
Estimating resource and reserves crosses the disciplines between geoscientists and petroleum engineers. While the geoscientist may well have primary responsibility, the engineer must carry the resource and reserve models forward for planning and economics. Volumetric estimates of reserves are among the most common examples of Monte Carlo simulation. Consider the following typical volumetric formula to calculate the gas in place, G, in standard cubic feet. In this formula, there is one component that identifies the prospect, A, while the other factors essentially modify this component.
The drilling conditions described above have led to the following practices, which are reasonably uniform, in the geothermal drilling industry. Because of the hard, fractured formations, roller-cone bits with tungsten-carbide inserts are almost universally used for geothermal drilling. The abrasive rocks mean that bit life is usually low (50 to 100 m), but many bits are also pulled because of bearing failures caused by rough drilling and high temperature. Polycrystalline diamond compact (PDC) bits have the dual advantages of more efficient rock cutting and no moving parts, but experience with PDC bits in geothermal drilling is both scant and unfavorable. Much research and development in hard-rock PDC bits is under way, so it is possible that these bits will come into wider use in geothermal drilling.
In certain situations, it is necessary to obtain a reliable measurement for connate water saturation (Swc) in an oil reservoir. The single well chemical tracer (SWCT) method has been used successfully for this purpose. The SWCT method has been used successfully for this purpose in six reservoirs. The SWCT test for Swc usually is carried out on wells that are essentially 100% oil producers. The procedure is analogous to the SWCT method for Sor, taking into account that oil is the mobile phase and water is stationary in the pore space.
The single-well chemical tracer (SWCT) test is an in-situ method for measuring fluid saturations in reservoirs. Most often, residual oil saturation is measured; less frequently, connate water saturation (Swc) is the objective. Either saturation is measured where one phase effectively is stationary in the pore space (i.e., is at residual saturation) and the other phase can flow to the wellbore. Recently, the SWCT method has been extended to measure oil/water fractional flow at measured fluid saturations in situations in which both oil and water phases are mobile. The SWCT test is used primarily to quantify the target oil saturation before initiating improved oil recovery (IOR) operations, to measure the effectiveness of IOR agents in a single well pilot and to assess a field for bypassed oil targets.
Interwell tracer tests are widely used. This article reviews some of the studies reported in open literature. The selection introduces different problems that have been addressed, but the original papers should be studied to obtain a more detailed description of the programs. The Snorre field is a giant oil reservoir (sandstone) in the Norwegian sector of the North Sea. Injection water and gas were monitored with tracers, 18 and the resulting tracer measurements are discussed in this page.
Techniques described in this page are classic methods for describing immiscible displacement assuming equilibrium between injected gas and displaced oil phases while accounting for differing physical characteristics of the fluids, the effects of reservoir heterogeneities, and injection/production well configurations. Included are modifications to typical displacement equations, evaluating sweep efficiency, and calculating performance. In simple calculations, the reservoir is treated in terms of average properties for volume of rock, and production performance is described on the basis of an average well. Black-oil-type reservoir simulation models use essentially these same techniques but, by means of 1D, 2D, or 3D cell arrays, account for areal and vertical variations in rock and fluid properties, well-to-well gravity effects, and individual well characteristics. More complex compositional models account for nonequilibrium conditions between injected and displaced fluids and can be used to describe individual well streams in terms of the compositions of the produced fluids.
This page discusses various aspects of gas reservoir performance, primarily to determine initial gas in place and how much is recoverable. The equations developed can used to form the basis of forecasting future production rates by capturing the relationship between cumulative fluid production and average reservoir pressure. Material-balance equations provide a relationship between original fluids in place, cumulative fluid production, and average reservoir pressure. This equation is the basis for the p/z-vs.-Gp Reservoir engineers have often used pressure contour maps or some approximate methods to determine field average reservoir pressure for p/z analysis. Usually, however, individual well pressures are based on extrapolation of pressure buildup tests or from long shut-in periods. In either case, the average pressure measured does not represent a point value, but rather is the average value within the well's effective drainage volume (see Estimating drainage shapes).
The implications of these compositional effects are very dependent on the oil composition, the composition of the injected gas, and the surface facilities and pipelines available in a particular field situation. The injected gas/oil composition interactions can be categorized as either swelling effects (gas dissolving into the oil phase) or stripping effects (various components from the oil transferring to the gas phase). The most obvious compositional effect in the immiscible gas/oil displacement process is that, if the oil is not saturated with gas at the reservoir pressure or if the reservoir pressure is increased as a result of the gas injection, the volume of gas dissolved in the oil will increase until the oil is saturated at that pressure. At the same time and because of the increased volume of gas in solution in the oil, the oil formation volume factor (FVF) will increase. This phenomenon, commonly called swelling, can increase the efficiency of the gas/oil displacement process.
This page discusses the primary manner in which the immiscible gas/oil displacement process has been used in qualitative terms. This is the use of gas injection high on structure to displace oil downdip toward the production wells that are completed low in the oil column. In many cases, an original gas cap was present, so the gas was injected into that gas cap interval (see Figure 1 for cross-sectional view of anticlinal reservoir with gas cap over oil column with dip angle α and thickness h). In this situation, the force of gravity is at work, trying to stabilize the downward gas/oil displacement process by keeping the gas on top of the oil and counteracting the unstable gas/oil viscous displacement process. If the oil production rate is kept below the critical rate, then the gas/oil contact (GOC) will move downward at a uniform rate.
Miscible injection is a proven, economically viable process that significantly increases oil recovery from many different types of reservoirs. Most miscible flooding projects use CO2 or nitrogen as solvents to increase oil recovery, but other injectants are sometimes used. This page provides an overview of the fundamental concepts of miscible displacement. Also provided are links to additional pages about designing a miscible flood, predicting the benefits of miscible injection, and a summary of field applications. Fieldwide projects have been implemented in fields around the world, with most of these projects being onshore North American fields.